正文
I.MX6 Manufacturing Tool V2 (MFGTool2) ucl2.xml hacking
提示：扫一扫查出行【扫一扫了解最新限行尾号】
复制提示
<!--
* Copyright (C) 2010-2013, Freescale Semiconductor, Inc. All Rights Reserved.
* The CFG element contains a list of recognized usb devices.
* DEV elements provide a name, class, vid and pid for each device.
*
* Each LIST element contains a list of update instructions.
* "Install" - Erase media and install firmware.
* "Update" - Update firmware only.
*
* Each CMD element contains one update instruction of attribute type.
* "pull" - Does UtpRead(body, file) transaction.
* "push" - Does UtpWrite(body, file) transaction.
* "drop" - Does UtpCommand(body) then waits for device to disconnect.
* "boot" - Finds configured device, forces it to "body" device and downloads "file".
* "find" - Waits for "timeout" seconds for the "body" device to connect.
* "show" - Parse and show device info in "file".
--><!--
参考文章：
1. dd命令的conv=fsync,oflag=sync/dsync：
http://blog.csdn.net/menogen/article/details/38059671
--><UCL>
<CFG>
<STATE name="BootStrap" dev="MX6D" vid="15A2" pid="0061"/>
<STATE name="Updater" dev="MSC" vid="066F" pid="37FF"/>
</CFG>
<!--
The following Lists are for i.MX6Solo/DualLite chips
--><!-- 名字叫：MYZR-I.MX6-SPI_NOR & eMMC的指令集，描述是：Choose SPI-NOR/eMMC as media -->
<LIST name="MYZR-I.MX6-SPI_NOR & eMMC" desc="Choose SPI-NOR/eMMC as media">
<!-- 启动第一阶段，加载u-boot.bin，这里不需要指定地址，不知道为什么 -->
<CMD state="BootStrap" type="boot" body="BootStrap" file ="myzr_u-boot.bin" >Loading uboot.</CMD>
<!-- 启动第一阶段，加载uImage，指定加载到0x10800000 -->
<CMD state="BootStrap" type="load" file="uImage" address="0x10800000"
loadSection="OTH" setSection="OTH" HasFlashHeader="FALSE" >Doing Kernel.</CMD>
<!-- initramfs: 最初的想法是Linus提出的，把cache当作文件系统装载。-->
<CMD state="BootStrap" type="load" file="initramfs.cpio.gz.uboot" address="0x10C00000"
loadSection="OTH" setSection="OTH" HasFlashHeader="FALSE" >Doing Initramfs.</CMD>
<!-- 跳到uImage的地方去执行，也就意味着uImage必须放在0x10800000 -->
<CMD state="BootStrap" type="jump" > Jumping to OS image. </CMD> <!--burn the uboot to SPI-NOR: -->
<!-- 不存在SPI-NOR，所以不需要了 -->
<!--
<CMD state="Updater" type="push" body="$ flash_erase /dev/mtd0 0 0">Erasing Boot partition</CMD>
<CMD state="Updater" type="push" body="send" file="files/u-boot.bin">Sending U-Boot</CMD>
<CMD state="Updater" type="push" body="$ dd if=$FILE of=/dev/mtd0 bs=512">write U-Boot to SPI-NOR</CMD>
--> <!-- partitioning the eMMC: -->
<!--
目前还不知道这里是用来做什么的，另外，从烧写、测试的过程来看，这里是不需要这条命令的，因为加了这条
命令，系统无法启动，而且总是会处于USB软件下载的状态。如果不小心运行着这条命令，想要改回之前的状态，
可以将命令参数8改成0，经过测试，这样是可行的，目前不知道是为什么。
-->
<CMD state="Updater" type="push" body="$ echo 8 > /sys/devices/platform/sdhci-esdhc-imx.3/mmc_host/mmc0/mmc0:0001/boot_config">access user partition and enable boot partion 1 to boot</CMD>
<!-- 发送分区文件到目标机 -->
<CMD state="Updater" type="push" body="send" file="mksdcard.sh.tar">Sending partition shell</CMD>
<!-- 解包分区文件 -->
<CMD state="Updater" type="push" body="$ tar xf $FILE "> Partitioning...</CMD>
<!-- 对设备/dev/mmcblk0进行分区，也就是对对应的mmc进行分区，分区情况请参考mksdcard.sh.tar -->
<CMD state="Updater" type="push" body="$ sh mksdcard.sh /dev/mmcblk0"> Partitioning SD card now...</CMD> <!-- burn the uboot: -->
<!-- 发送u-boot到目标机中 -->
<CMD state="Updater" type="push" body="send" file="files/u-boot.bin">Sending U-Boot</CMD>
<!-- 擦除mmcblk0的1k（512*2=1k）字节到1M（512*2000=1M）emmc，最前面的1k字节貌似保存了emmc分区表的 -->
<CMD state="Updater" type="push" body="$ dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=2 count=2000">Clean U-Bootenvironment</CMD>
<!-- 将上面发送到目标机的u-boot写入emmc中，从emmc的1k（512*2=1k）的地方开始，这里不知道我们是不是一定要从这个地址开始写 -->
<CMD state="Updater" type="push" body="$ dd if=$FILE of=/dev/mmcblk0 bs=512 seek=2 skip=2">write U-Boot to sdcard</CMD> <!-- burn the kernel: -->
<!-- 发送uImage到目标机中 -->
<CMD state="Updater" type="push" body="send" file="files/uImage">Sending kernel uImage</CMD>
<!--
conv=fsync: Synchronize output data and metadata just before finishing 意思也就是在dd命令结束前同步data和metadata，那就是不是每一次写都同步一次咯，也就是如果我们在dd命令中写了100次，他可能是等到最后的时候才把他们同步到磁盘。
oflag=dsync: Use synchronized I/O for data. For the output file, this forces a physical write of output data on each write，注意这里边用词 a physical write of output data on each write,那就是他是每一次写都得等到这一次写写到了磁盘才进行下一个写，也就是如果我们使用dd写100次，他每次写都是写到磁盘后才进行下一次写的。 将前面发送的目标机的uImage写入emmc中，从1M的地方开始写，同样不知道是不是一定要从这个位置开始写
-->
<CMD state="Updater" type="push" body="$ dd if=$FILE of=/dev/mmcblk0 bs=1M seek=1 conv=fsync">write kernel image to emmc</CMD> <!-- burn the rootfs: -->
<!-- ext3格式格式化emmc的第一个分区，这是文件系统分区 -->
<CMD state="Updater" type="push" body="$ mkfs.ext3 -j /dev/mmcblk0p1">Formatting rootfs partition</CMD>
<!-- 创建/mnt/mmcblk0p1文件夹 -->
<CMD state="Updater" type="push" body="$ mkdir -p /mnt/mmcblk0p1"/>
<!-- 以ext3格式挂载emmc的第一个分区到/mnt/mmcblk0p1文件夹 -->
<CMD state="Updater" type="push" body="$ mount -t ext3 /dev/mmcblk0p1 /mnt/mmcblk0p1"/>
<!-- 采用pipe的方式传输大文件，主要是防止文件过大，并大于内存，解压rootfs.tar.bz2文件到emmc第一个分区中 -->
<CMD state="Updater" type="push" body="pipe tar -jxv -C /mnt/mmcblk0p1" file="files/rootfs.tar.bz2">Sending and writting rootfs</CMD>
<!-- flush内存中的数据到emmc中 -->
<CMD state="Updater" type="push" body="frf">Finishing rootfs write</CMD>
<!-- 卸载挂载在/mnt/mmcblk0p1上的分区 -->
<CMD state="Updater" type="push" body="$ umount /mnt/mmcblk0p1">Unmounting rootfs partition</CMD> <!-- 提示更新系统完毕 -->
<CMD state="Updater" type="push" body="$ echo Update Complete!">Done</CMD>
</LIST> <!-- 名字叫：MYZR-I.MX6-SPI_NOR & SD card的指令集，描述是：Choose SPI-NOR/SD as media -->
<LIST name="MYZR-I.MX6-SPI_NOR & SD card" desc="Choose SPI-NOR/SD as media">
<!-- 第一阶段，将u-boot下载到目标机上，这里没有指定起始地址 -->
<CMD state="BootStrap" type="boot" body="BootStrap" file ="myzr_u-boot.bin" >Loading uboot.</CMD>
<!--
第一阶段，将uImage下载到内存地址的0x10800000的地方，不知道为什么要下载到这个地方.
-->
<CMD state="BootStrap" type="load" file="uImage" address="0x10800000"
loadSection="OTH" setSection="OTH" HasFlashHeader="FALSE" >Doing Kernel.</CMD>
<!-- 第一阶段，将initramfs文件系统发送到目标机上，起始地址是0x10C00000 -->
<CMD state="BootStrap" type="load" file="initramfs.cpio.gz.uboot" address="0x10C00000"
loadSection="OTH" setSection="OTH" HasFlashHeader="FALSE" >Doing Initramfs.</CMD>
<!--
跳转到uImage的地方开始运行，从这里可以看出，系统是知道内核在哪里的，而前面又正好将uImage放在
0x10800000的地方，应该是系统中已经设置好了这个值
-->
<CMD state="BootStrap" type="jump" > Jumping to OS image. </CMD> <!--burn the uboot to SPI-NOR: -->
<!--
这一部分的目标是将U-Boot放入SPI-NOR中，也就意味着U-Boot是从SPI-NOR中开始引导启动
-->
<CMD state="Updater" type="push" body="$ flash_erase /dev/mtd0 0 0">Erasing Boot partition</CMD>
<CMD state="Updater" type="push" body="send" file="files/u-boot.bin">Sending U-Boot</CMD>
<CMD state="Updater" type="push" body="$ dd if=$FILE of=/dev/mtd0 bs=512">write U-Boot to SPI-NOR</CMD> <!-- partitioning the SD card: -->
<!--
对SD卡进行分区，这里的SD的设备节点是：/dev/mmcblk1，也就是说SD卡挂在在emmc总线的第二个上面
-->
<CMD state="Updater" type="push" body="send" file="mksdcard.sh.tar">Sending partition shell</CMD>
<CMD state="Updater" type="push" body="$ tar xf $FILE "> Partitioning...</CMD>
<CMD state="Updater" type="push" body="$ sh mksdcard.sh /dev/mmcblk1"> Partitioning SD card now...</CMD> <!-- burn the kernel: -->
<!-- 将内核烧入SD卡的中，从SD卡的1M的地方开始烧写 -->
<CMD state="Updater" type="push" body="send" file="files/uImage">Sending kernel uImage</CMD>
<CMD state="Updater" type="push" body="$ dd if=$FILE of=/dev/mmcblk1 bs=1M seek=1 conv=fsync">write kernel image to sd card</CMD> <!-- burn the rootfs: -->
<!-- 以ext3的方式格式化分区1，并将文件系统的文件解压放到这个分区中去 -->
<CMD state="Updater" type="push" body="$ mkfs.ext3 -j /dev/mmcblk1p1">Formatting rootfs partition</CMD>
<CMD state="Updater" type="push" body="$ mkdir -p /mnt/mmcblk1p1"/>
<CMD state="Updater" type="push" body="$ mount -t ext3 /dev/mmcblk1p1 /mnt/mmcblk1p1"/>
<CMD state="Updater" type="push" body="pipe tar -jxv -C /mnt/mmcblk1p1" file="files/rootfs.tar.bz2">Sending and writting rootfs</CMD>
<CMD state="Updater" type="push" body="frf">Finishing rootfs write</CMD>
<CMD state="Updater" type="push" body="$ umount /mnt/mmcblk1p1">Unmounting rootfs partition</CMD> <!-- 提示更新完毕 -->
<CMD state="Updater" type="push" body="$ echo Update Complete!">Done</CMD>
</LIST><!-- 名字叫：MYZR-I.MX6-UBUNTU-SPI_NOR & eMMC的指令集，描述是：Choose eMMC as media -->
<LIST name="MYZR-I.MX6-UBUNTU-SPI_NOR & eMMC" desc="Choose eMMC as media">
<!--
第一阶段，将u-boot下载到目标机上，这里没有指定起始地址
第一阶段，将uImage下载到内存地址的0x10800000的地方，不知道为什么要下载到这个地方.
第一阶段，将initramfs文件系统发送到目标机上，起始地址是0x10C00000
跳转到uImage的地方开始运行，从这里可以看出，系统是知道内核在哪里的，而前面又正好将uImage放在
0x10800000的地方，应该是系统中已经设置好了这个值
-->
<CMD state="BootStrap" type="boot" body="BootStrap" file ="myzr_u-boot.bin" >Loading U-boot</CMD>
<CMD state="BootStrap" type="load" file="uImage" address="0x10800000"
loadSection="OTH" setSection="OTH" HasFlashHeader="FALSE" >Loading Kernel.</CMD>
<CMD state="BootStrap" type="load" file="initramfs.cpio.gz.uboot" address="0x10C00000"
loadSection="OTH" setSection="OTH" HasFlashHeader="FALSE" >Loading Initramfs.</CMD>
<CMD state="BootStrap" type="jump" > Jumping to OS image. </CMD> <!--burn the uboot to SPI-NOR: -->
<!--
这一部分的目标是将U-Boot放入SPI-NOR中，也就意味着U-Boot是从SPI-NOR中开始引导启动
-->
<CMD state="Updater" type="push" body="$ flash_erase /dev/mtd0 0 0">Erasing Boot partition</CMD>
<CMD state="Updater" type="push" body="send" file="files/u-boot.bin">Sending U-Boot</CMD>
<CMD state="Updater" type="push" body="$ dd if=$FILE of=/dev/mtd0 bs=512">write U-Boot to SPI-NOR</CMD> <!-- partitioning the eMMC: -->
<!--
对SD卡进行分区，这里的SD的设备节点是：/dev/mmcblk0，也就是说SD卡挂在在emmc总线的第二个上面
-->
<CMD state="Updater" type="push" body="$ echo 8 > /sys/devices/platform/sdhci-esdhc-imx.3/mmc_host/mmc0/mmc0:0001/boot_config">access user partition and enable boot partion 1 to boot</CMD>
<CMD state="Updater" type="push" body="send" file="mksdcard.sh.tar">Sending partition shell</CMD>
<CMD state="Updater" type="push" body="$ tar xf $FILE "> Partitioning...</CMD>
<CMD state="Updater" type="push" body="$ sh mksdcard.sh /dev/mmcblk0"> Partitioning SD card now...</CMD> <!-- burn the kernel: -->
<!-- 将内核烧入emmc卡的中，从emmc卡的1M的地方开始烧写 -->
<CMD state="Updater" type="push" body="send" file="files/uImage">Sending kernel uImage</CMD>
<CMD state="Updater" type="push" body="$ dd if=$FILE of=/dev/mmcblk0 bs=1M seek=1 conv=fsync">write kernel image to emmc</CMD> <!-- burn the rootfs: -->
<!-- 以ext3的方式格式化分区1，并将文件系统的文件解压放到这个分区中去 -->
<CMD state="Updater" type="push" body="$ mkfs.ext3 -j /dev/mmcblk0p1">Formatting rootfs partition</CMD>
<CMD state="Updater" type="push" body="$ mkdir -p /mnt/mmcblk0p1"/>
<CMD state="Updater" type="push" body="$ mount -t ext3 /dev/mmcblk0p1 /mnt/mmcblk0p1"/>
<CMD state="Updater" type="push" body="pipe tar --numeric-owner -zxv -C /mnt/mmcblk0p1" file="files/oneiric12.04LTS.tgz">Sending and writting rootfs</CMD>
<CMD state="Updater" type="push" body="frf">Finishing rootfs write</CMD>
<CMD state="Updater" type="push" body="$ umount /mnt/mmcblk0p1">Unmounting rootfs partition</CMD>
<CMD state="Updater" type="push" body="$ echo Update Complete!">Done</CMD>
</LIST><LIST name="Android-MYZR-SPI_NOR-eMMC" desc="Choose SPI-NOR and SD Rootfs as media"> <CMD state="BootStrap" type="boot" body="BootStrap" file ="myzr_u-boot.bin" >Loading U-boot</CMD>
<CMD state="BootStrap" type="load" file="uImage" address="0x10800000"
loadSection="OTH" setSection="OTH" HasFlashHeader="FALSE" >Loading Kernel.</CMD>
<CMD state="BootStrap" type="load" file="initramfs.cpio.gz.uboot" address="0x10C00000"
loadSection="OTH" setSection="OTH" HasFlashHeader="FALSE" >Loading Initramfs.</CMD>
<CMD state="BootStrap" type="jump" > Jumping to OS image. </CMD> <!--
Please use "cat /proc/mtd" to check the right partitions for NAND
,mtd0 and mtd1 are for SPI-NOR; mtd2 - mtd6 are for NAND
-->
<!--
<CMD state="Updater" type="push" body="mknod class/mtd,mtd0,/dev/mtd0"/>
<CMD state="Updater" type="push" body="mknod block,mtdblock0,/dev/mtdblock0,block"/>
-->
<!--
<CMD state="Updater" type="push" body="$ flash_erase /dev/mtd0 0 0">Erasing Boot partition</CMD>
<CMD state="Updater" type="push" body="send" file="files/android/u-boot.bin">Sending U-Boot</CMD>
<CMD state="Updater" type="push" body="$ dd if=$FILE of=/dev/mtd0 bs=512">write U-Boot to SPI-NOR</CMD>
--> <!-- 对emmc进行分区-->
<CMD state="Updater" type="push" body="send" file="mksdcard-android.sh.tar">Sending partition shell</CMD>
<CMD state="Updater" type="push" body="$ tar xf $FILE "> Partitioning...</CMD>
<CMD state="Updater" type="push" body="$ sh mksdcard-android.sh /dev/mmcblk0"> Partitioning...</CMD>
<CMD state="Updater" type="push" body="$ ls -l /dev/mmc* ">Formatting sd partition</CMD> <!-- burn the uboot: -->
<!-- 发送u-boot到目标机中 -->
<!-- 擦除mmcblk0的1k（512*2=1k）字节到1M（512*2000=1M）emmc，最前面的1k字节貌似保存了emmc分区表的 -->
<!-- 将上面发送到目标机的u-boot写入emmc中，从emmc的1k（512*2=1k）的地方开始，这里不知道我们是不是一定要从这个地址开始写 --> <CMD state="Updater" type="push" body="send" file="files/android/u-boot.bin">Sending U-Boot</CMD>
<CMD state="Updater" type="push" body="$ dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=2 count=2000">Clean U-Bootenvironment</CMD>
<CMD state="Updater" type="push" body="$ dd if=$FILE of=/dev/mmcblk0 bs=512 seek=2 skip=2">write U-Boot to sdcard</CMD> <!-- burn the uImage: -->
<!-- 将boot.img文件写入mmcblk0p1分区 -->
<CMD state="Updater" type="push" body="send" file="files/android/boot.img">Sending kernel uImage</CMD>
<CMD state="Updater" type="push" body="$ dd if=$FILE of=/dev/mmcblk0p1">write boot.img</CMD>
<CMD state="Updater" type="push" body="frf">flush the memory.</CMD> <!-- 对分区4、5、6、7进行格式化，以ext3的文件系统格式进行格式化 -->
<CMD state="Updater" type="push" body="$ mkfs.ext4 -L data /dev/mmcblk0p4">Formatting sd partition</CMD>
<CMD state="Updater" type="push" body="$ mkfs.ext4 -L system /dev/mmcblk0p5">Formatting system partition</CMD>
<CMD state="Updater" type="push" body="$ mkfs.ext4 -L cache -O^extent /dev/mmcblk0p6">Formatting cache partition</CMD>
<CMD state="Updater" type="push" body="$ mkfs.ext4 -L vender /dev/mmcblk0p7">Formatting data partition</CMD>
<CMD state="Updater" type="push" body="frf">flush the memory.</CMD> <!-- 将文件系统写入rootfs分区中，使用pipe方式传输 -->
<CMD state="Updater" type="push" body="$ mkfs.ext4 /dev/mmcblk0p8">Formatting misc partition</CMD>
<CMD state="Updater" type="push" body="pipe dd of=/dev/mmcblk0p5 bs=512" file="files/android/system.img">Sending and writting system.img</CMD>
<CMD state="Updater" type="push" body="frf">flush the memory.</CMD>
<!-- Write userdata.img is optional, for some customer this is needed, but it's optional. -->
<!-- Also, userdata.img will have android unit test, you can use this to do some auto test. -->
<!--
<CMD state="Updater" type="push" onError="ignore" body="pipe dd of=/dev/mmcblk0p7" file="file/android/userdate.img"> Sending userdata.img(optional) </CMD>
<CMD state="Updater" type="push" body="frf">flush the memory.</CMD>
--> <!-- 将recovery镜像写入第二个分区中-->
<CMD state="Updater" type="push" body="pipe dd of=/dev/mmcblk0p2 bs=512" file="files/android/recovery.img">Sending and writting recovery.img</CMD>
<CMD state="Updater" type="push" body="frf">Finishing rootfs write</CMD> <!-- 提示更新完毕 -->
<CMD state="Updater" type="push" body="$ echo Update Complete!">Done</CMD>
</LIST> </UCL>
