在树莓派上运行 .net core 2.1 程序并实现开机启动

提示：扫一扫查出行
【扫一扫了解最新限行尾号】
复制提示

本篇文章完整的说明如和在树莓派上运行 .net core2.1程序，当然也参考了其他的博客，此处结合我自己的经验，再写一篇完整的博客，方便大家，还有我自己进行查阅。

https://blog.csdn.net/weixin_39449466/article/details/80686835

https://blog.csdn.net/sD7O95O/article/details/79395766

https://blog.csdn.net/github_35160620/article/details/52134098

http://shumeipai.nxez.com/2013/10/06/windows-remote-desktop-connection-raspberry-pi.html

https://blog.csdn.net/guanmaoning/article/details/78760428

ok，接下来进入正题，先弄个树莓派，如果都没有，那还玩什么东西。。。。。

准备一个tf卡，准备读卡器，现在要往tf写入操作系统。

官方的地址：https://www.raspberrypi.org/downloads/raspbian/

推荐下载下面的：

下载好之后，准备格式化tf卡

需要下载一个软件（我看教程都是下载软件，系统默认格式化我也不知道行不行，可能格式有区别）

格式化工具：SD card formatter

将下载好的系统镜像写入tf卡

写入工具：win32diskimager

开启ssh连接

在tf卡当前的目录下创建一个文件，命名为 ssh 不带任何的后缀

设置无线网连接

country=CN
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1network={
ssid="AMRHU"
psk="12345678"
key_mgmt=WPA-PSK
priority=1
}

这样开机后就能连接上网络。

显示设置

在boot目录下，找到config.txt文件，里面许多选项被注释掉了，我们需要在选择以下命令：

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
disable_overscan=1#可以去掉开机屏幕周围的黑色边框# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1## uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2#DMT模式
hdmi_mode=58 #分辨率为适应屏幕分辨率的选择# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
hdmi_drive=2# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
config_hdmi_boost=4# uncomment for composite PAL
#sdtv_mode=2#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi# Additional overlays and parameters are documented /boot/overlays/README# Enable audio (loads snd_bcm2835)
dtparam=audio=on