正文
MPSOC之3——centos环境配置及petalinux安装及使用
提示：扫一扫查出行【扫一扫了解最新限行尾号】
复制提示
ubuntu虽然能正常安装，但是build时会出现闪退情况，闪退后一切归零，没啥错误提示，改用centos来安装petalinux。
0.环境
vmware pro 14，centos 7.3
petalinux 2017.2
1.petalinux安装环境配置
除了python,其他都用yum直接安装即可,安装UG1144里的所有库
python安装过程：
wget https://www.python.org/ftp/python/3.4.1/Python-3.4.1.tgz
tar xf Python-3.4.1.tgz
cd Python-3.4.1
./configure
make
make install
安装到/usr/local/bin/python3目录了，在/usr/bin/中创建指向该位置的符号连接
ln -s /usr/local/bin/python3 /usr/bin/python3
2.安装及配置
[root@localhost opt]# chown liuwanpeng:liuwanpeng -R /opt
[root@localhost opt]# ls / -lh
总用量 28K
......
drwxr-xr-x. 3 root root 18 12月 4 14:01 mnt
drwxr-xr-x. 4 liuwanpeng liuwanpeng 27 12月 4 14:40 opt
dr-xr-xr-x. 223 root root 0 12月 4 16:15 proc
......
[root@localhost opt]# su liuwanpeng
[liuwanpeng@localhost ~]$ ./petalinux-v2017.2-final-installer.run /opt/pkg/petalinux
INFO: Checking installer checksum...
INFO: Extracting PetaLinux installer...
INFO: Installing PetaLinux...
INFO: Checking PetaLinux installer integrity...
INFO: Extracting Installation files...
LICENSE AGREEMENTS
PetaLinux SDK contains software from a number of sources. Please review
the following licenses and indicate your acceptance of each to continue.
You do not have to accept the licenses, however if you do not then you may
not use PetaLinux SDK.
Use PgUp/PgDn to navigate the license viewer, and press 'q' to close
Press Enter to display the license agreements
Do you accept Xilinx End User License Agreement? [y/N] > y
Do you accept Webtalk Terms and Conditions? [y/N] > y
Do you accept Third Party End User License Agreement? [y/N] > y
INFO: Checking installation environment requirements...
INFO: Checking free disk space
INFO: Checking installed tools
INFO: Checking installed development libraries
INFO: Checking network and other services
WARNING: No tftp server found - please refer to "PetaLinux SDK Installation Guide" for its impact and solution
INFO: Installing PetaLinux SDK to "/opt/pkg/petalinux/."
INFO: Installing PetaLinux zynqMP Yocto SDK to "/opt/pkg/petalinux/./components/yocto/source/aarch64"...
PetaLinux Extensible SDK installer version 2017.2
=================================================
You are about to install the SDK to "/opt/pkg/petalinux/components/yocto/source/aarch64". Proceed[Y/n]? Y
Extracting SDK.............................................done
Setting it up...
Extracting buildtools...
done
SDK has been successfully set up and is ready to be used.
Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g.
$ . /opt/pkg/petalinux/components/yocto/source/aarch64/environment-setup-aarch64-xilinx-linux
INFO: PetaLinux Yocto SDK for zynqMP has been successfully installed.
INFO: Installing PetaLinux zynq Yocto SDK to "/opt/pkg/petalinux/./components/yocto/source/arm"...
PetaLinux Extensible SDK installer version 2017.2
=================================================
You are about to install the SDK to "/opt/pkg/petalinux/components/yocto/source/arm". Proceed[Y/n]? Y
Extracting SDK.........................................done
Setting it up...
Extracting buildtools...
done
SDK has been successfully set up and is ready to be used.
Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g.
$ . /opt/pkg/petalinux/components/yocto/source/arm/environment-setup-cortexa9hf-neon-xilinx-linux-gnueabi
INFO: PetaLinux Yocto SDK for zynq has been successfully installed.
INFO: Installing PetaLinux microblaze (Full) Yocto SDK to "/opt/pkg/petalinux/./components/yocto/source/microblaze_full"...
PetaLinux Extensible SDK installer version 2017.2
=================================================
You are about to install the SDK to "/opt/pkg/petalinux/components/yocto/source/microblaze_full". Proceed[Y/n]? Y
Extracting SDK.............................done
Setting it up...
Extracting buildtools...
done
SDK has been successfully set up and is ready to be used.
Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g.
$ . /opt/pkg/petalinux/components/yocto/source/microblaze_full/environment-setup-microblazeel-v10.0-bs-cmp-mh-div-xilinx-linux
INFO: Installing PetaLinux microblaze (Lite) Yocto SDK to "/opt/pkg/petalinux/./components/yocto/source/microblaze_lite"...
PetaLinux Extensible SDK installer version 2017.2
=================================================
You are about to install the SDK to "/opt/pkg/petalinux/components/yocto/source/microblaze_lite". Proceed[Y/n]? Y
Extracting SDK.............................done
Setting it up...
Extracting buildtools...
done
SDK has been successfully set up and is ready to be used.
Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g.
$ . /opt/pkg/petalinux/components/yocto/source/microblaze_lite/environment-setup-microblazeel-v10.0-bs-cmp-ml-xilinx-linux
INFO: PetaLinux Yocto SDK for microblaze has been successfully installed.
INFO: PetaLinux SDK has been installed to /opt/pkg/petalinux/.
[liuwanpeng@localhost ~]$ source /opt/pkg/petalinux/settings.sh
PetaLinux environment set to '/opt/pkg/petalinux'
INFO: Checking free disk space
INFO: Checking installed tools
INFO: Checking installed development libraries
INFO: Checking network and other services
WARNING: No tftp server found - please refer to "PetaLinux SDK Installation Guide" for its impact and solution
[root@localhost opt]# chown liuwanpeng:liuwanpeng -R /opt
[root@localhost opt]# ls / -lh
总用量 28K
......
drwxr-xr-x. 3 root root 18 12月 4 14:01 mnt
drwxr-xr-x. 4 liuwanpeng liuwanpeng 27 12月 4 14:40 opt
dr-xr-xr-x. 223 root root 0 12月 4 16:15 proc
......
[root@localhost opt]# su liuwanpeng
[liuwanpeng@localhost ~]$ ./petalinux-v2017.2-final-installer.run /opt/pkg/petalinux
INFO: Checking installer checksum...
INFO: Extracting PetaLinux installer...
INFO: Installing PetaLinux...
INFO: Checking PetaLinux installer integrity...
INFO: Extracting Installation files...
LICENSE AGREEMENTS
PetaLinux SDK contains software from a number of sources. Please review
the following licenses and indicate your acceptance of each to continue.
You do not have to accept the licenses, however if you do not then you may
not use PetaLinux SDK.
Use PgUp/PgDn to navigate the license viewer, and press 'q' to close
Press Enter to display the license agreements
Do you accept Xilinx End User License Agreement? [y/N] > y
Do you accept Webtalk Terms and Conditions? [y/N] > y
Do you accept Third Party End User License Agreement? [y/N] > y
INFO: Checking installation environment requirements...
INFO: Checking free disk space
INFO: Checking installed tools
INFO: Checking installed development libraries
INFO: Checking network and other services
WARNING: No tftp server found - please refer to "PetaLinux SDK Installation Guide" for its impact and solution
INFO: Installing PetaLinux SDK to "/opt/pkg/petalinux/."
INFO: Installing PetaLinux zynqMP Yocto SDK to "/opt/pkg/petalinux/./components/yocto/source/aarch64"...
PetaLinux Extensible SDK installer version 2017.2
=================================================
You are about to install the SDK to "/opt/pkg/petalinux/components/yocto/source/aarch64". Proceed[Y/n]? Y
Extracting SDK.............................................done
Setting it up...
Extracting buildtools...
done
SDK has been successfully set up and is ready to be used.
Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g.
$ . /opt/pkg/petalinux/components/yocto/source/aarch64/environment-setup-aarch64-xilinx-linux
INFO: PetaLinux Yocto SDK for zynqMP has been successfully installed.
INFO: Installing PetaLinux zynq Yocto SDK to "/opt/pkg/petalinux/./components/yocto/source/arm"...
PetaLinux Extensible SDK installer version 2017.2
=================================================
You are about to install the SDK to "/opt/pkg/petalinux/components/yocto/source/arm". Proceed[Y/n]? Y
Extracting SDK.........................................done
Setting it up...
Extracting buildtools...
done
SDK has been successfully set up and is ready to be used.
Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g.
$ . /opt/pkg/petalinux/components/yocto/source/arm/environment-setup-cortexa9hf-neon-xilinx-linux-gnueabi
INFO: PetaLinux Yocto SDK for zynq has been successfully installed.
INFO: Installing PetaLinux microblaze (Full) Yocto SDK to "/opt/pkg/petalinux/./components/yocto/source/microblaze_full"...
PetaLinux Extensible SDK installer version 2017.2
=================================================
You are about to install the SDK to "/opt/pkg/petalinux/components/yocto/source/microblaze_full". Proceed[Y/n]? Y
Extracting SDK.............................done
Setting it up...
Extracting buildtools...
done
SDK has been successfully set up and is ready to be used.
Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g.
$ . /opt/pkg/petalinux/components/yocto/source/microblaze_full/environment-setup-microblazeel-v10.0-bs-cmp-mh-div-xilinx-linux
INFO: Installing PetaLinux microblaze (Lite) Yocto SDK to "/opt/pkg/petalinux/./components/yocto/source/microblaze_lite"...
PetaLinux Extensible SDK installer version 2017.2
=================================================
You are about to install the SDK to "/opt/pkg/petalinux/components/yocto/source/microblaze_lite". Proceed[Y/n]? Y
Extracting SDK.............................done
Setting it up...
Extracting buildtools...
done
SDK has been successfully set up and is ready to be used.
Each time you wish to use the SDK in a new shell session, you need to source the environment setup script e.g.
$ . /opt/pkg/petalinux/components/yocto/source/microblaze_lite/environment-setup-microblazeel-v10.0-bs-cmp-ml-xilinx-linux
INFO: PetaLinux Yocto SDK for microblaze has been successfully installed.
INFO: PetaLinux SDK has been installed to /opt/pkg/petalinux/.
[liuwanpeng@localhost ~]$ source /opt/pkg/petalinux/settings.sh
PetaLinux environment set to '/opt/pkg/petalinux'
INFO: Checking free disk space
INFO: Checking installed tools
INFO: Checking installed development libraries
INFO: Checking network and other services
WARNING: No tftp server found - please refer to "PetaLinux SDK Installation Guide" for its impact and solution
每次打开termal时，上述命令需要重新输入，太麻烦。可以将该命令加入到~/.bashrc文件中，每次打开termal会自动执行该脚本。
// 关闭网络交互
[liuwanpeng@localhost ~]$ petalinux-util --webtalk off
INFO: Turn off webtalk feature!
3. 建工程
[liuwanpeng@localhost mpsoc]$ petalinux-create -t project -s ../xilinx-zcu102-v2017.2-final.bsp
INFO: Create project:
INFO: Projects:
INFO: * xilinx-zcu102-2017.2
INFO: has been successfully installed to /home/liuwanpeng/mpsoc/
INFO: New project successfully created in /home/liuwanpeng/mpsoc/
4.config
[liuwanpeng@localhost mpsoc]$ petalinux-create -t project -s ../xilinx-zcu102-v2017.2-final.bsp
INFO: Create project:
INFO: Projects:
INFO: * xilinx-zcu102-2017.2
INFO: has been successfully installed to /home/liuwanpeng/mpsoc/
INFO: New project successfully created in /home/liuwanpeng/mpsoc/
弹出的图形界面配置里不用动
[liuwanpeng@localhost xilinx-zcu102-2017.2]$ petalinux-config --get-hw-description=hardware/xilinx-zcu102-2017.2/xilinx-zcu102-2017.2.sdk/
INFO: Getting hardware description...
[INFO] generating Kconfig for project
[INFO] menuconfig project
/home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/misc/config/Kconfig.syshw:30:warning: defaults for choice values not supported
/home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/misc/config/Kconfig:574:warning: config symbol defined without type
configuration written to /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/project-spec/configs/config
*** End of the configuration.
*** Execute 'make' to start the build or try 'make help'.
[INFO] sourcing bitbake
[INFO] generating plnxtool conf
[INFO] generating meta-plnx-generated layer
~/mpsoc/xilinx-zcu102-2017.2/build/misc/plnx-generated ~/mpsoc/xilinx-zcu102-2017.2
~/mpsoc/xilinx-zcu102-2017.2
[INFO] generating machine configuration
[INFO] generating bbappends for project . This may take time !
~/mpsoc/xilinx-zcu102-2017.2/build/misc/plnx-generated ~/mpsoc/xilinx-zcu102-2017.2
~/mpsoc/xilinx-zcu102-2017.2
[INFO] generating u-boot configuration files
[INFO] generating kernel configuration files
[INFO] generating kconfig for Rootfs
Generate rootfs kconfig
[INFO] oldconfig rootfs
[INFO] generating petalinux-user-image.bb
5.build
总结：
-错误：install: cannot stat ‘/home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/../components/plnx_workspace/pmu-firmware/Release/pmu-firmware.elf’: No such file or directory
解决：缺库，安装libstdc++.i686,glibc-devel.i686,libz.so.1
-
timeout while establishing a connection with SDK
解决：AR# 69812没用，看论坛https://forums.xilinx.com/xlnx/board/crawl_message?board.id=EDK&message.id=41823
in fsbl and pmufw recipes add this two lines
export _JAVA_OPTIONS
_JAVA_OPTIONS = "-Duser.home=${TMPDIR}/xsctenv"
(1)出错了 install: cannot stat ‘/home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/../components/plnx_workspace/pmu-firmware/Release/pmu-firmware.elf’: No such file or directory
[liuwanpeng@localhost xilinx-zcu102-2017.2]$ petalinux-build
[INFO] building project
[INFO] sourcing bitbake
INFO: bitbake petalinux-user-image
Loading cache: 100% |############################################| Time: 0:00:02
Loaded 3235 entries from dependency cache.
Parsing recipes: 100% |##########################################| Time: 0:00:09
Parsing of 2446 .bb files complete (2407 cached, 39 parsed). 3236 targets, 224 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
Initialising tasks: 100% |#######################################| Time: 0:01:28
Checking sstate mirror object availability: 100% |###############| Time: 0:00:13
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
fsbl-2017.2+gitAUTOINC+122565ec40-r0 do_compile: NOTE: fsbl: compiling from external source tree /opt/pkg/petalinux/tools/hsm/data/embeddedsw
pmu-firmware-2017.2+gitAUTOINC+122565ec40-r0 do_compile: NOTE: pmu-firmware: compiling from external source tree /opt/pkg/petalinux/tools/hsm/data/embeddedsw
ERROR: pmu-firmware-2017.2+gitAUTOINC+122565ec40-r0 do_deploy: Function failed: do_deploy (log file is located at /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/temp/log.do_deploy.94828)
ERROR: Logfile of failure stored in: /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/temp/log.do_deploy.94828
Log data follows:
| DEBUG: Executing python function sstate_task_prefunc
| DEBUG: Python function sstate_task_prefunc finished
| DEBUG: Executing shell function do_deploy
| install: cannot stat ‘/home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/../components/plnx_workspace/pmu-firmware/Release/pmu-firmware.elf’: No such file or directory
| ERROR: Function failed: do_deploy (log file is located at /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/temp/log.do_deploy.94828)
ERROR: Task (/opt/pkg/petalinux/components/yocto/source/aarch64/layers/meta-xilinx-tools/recipes-bsp/pmu/pmu-firmware_git.bb:do_deploy) failed with exit code '1'
NOTE: Tasks Summary: Attempted 2399 tasks of which 1865 didn't need to be rerun and 1 failed.
Summary: 1 task failed:
/opt/pkg/petalinux/components/yocto/source/aarch64/layers/meta-xilinx-tools/recipes-bsp/pmu/pmu-firmware_git.bb:do_deploy
xilinx有专门的AR# 69293：跟上述问题还不是同一个
2017.1/2 Zynq UltraScale+ MPSoC: PetaLinux fails to build PMU Firmware on CentOS 7.2/3
Search for Another Answer
Description
Solution
Description
The 2017.1 release of PetaLinux fails to build PMUFW on CentOS 7.2/3 with a build error as shown below:
log.do_deploy:
install: cannot stat /home/wtsemb/Downloads/zcu102-centos-test/build/../components/plnx_workspace/pmu-firmware/Release/pmu-firmware.elf: No such file or directory
ERROR: Function failed: do_deploy (log file is located at /home/wtsemb/Downloads/zcu102-centos-test/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.1+gitAUTOINC+3813f14966-r0/temp/log.do_deploy.60209)
u
log.do_compile:
mb-gcc: error while loading shared libraries: libstdc++.so.6: wrong ELF class: ELFCLASS64
make[1]: *** [Makefile:25: xipipsu.o] Error 127
Solution
This can be due to missing packages which are required to build the PMUFW. The work-around for this issue is to install the packages below on the Linux host.
Once you install the packages and reboot Linux host, you can source PetaLinux tools and then create a new PetaLinux and build it.
libstdc++.i686
glibc-devel.i686
Was this Answer Record helpful?
光安装上述库有时不管用。直接查看log.do_deploy.94828之前的log文件，log.do_compile时有错误，缺少库
mb-ar: error while loading shared libraries: libz.so.1: cannot open shared object file: No such file or directory
(2) Checking sstate mirror object availability不动了，安装(1)的补丁之前无此问题，重启后问题消失
[liuwanpeng@localhost xilinx-zcu102-2017.2]$ petalinux-build
[INFO] building project
[INFO] sourcing bitbake
INFO: bitbake petalinux-user-image
Loading cache: 100% |############################################| Time: 0:00:03
Loaded 3235 entries from dependency cache.
Parsing recipes: 100% |##########################################| Time: 0:00:08
Parsing of 2446 .bb files complete (2407 cached, 39 parsed). 3236 targets, 224 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
Initialising tasks: 100% |#######################################| Time: 0:01:35
Checking sstate mirror object availability: 3% | | ETA: 0:04:30
Keyboard Interrupt, closing down...
（3）又来了新错误，"timeout while establishing a connection with SDK""
[liuwanpeng@localhost xilinx-zcu102-2017.2]$ petalinux-build
[INFO] building project
INFO: bitbake petalinux-user-image
Loading cache: 100% |############################################| Time: 0:00:02
Loaded 3235 entries from dependency cache.
Parsing recipes: 100% |##########################################| Time: 0:00:07
Parsing of 2446 .bb files complete (2407 cached, 39 parsed). 3236 targets, 224 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
Initialising tasks: 100% |#######################################| Time: 0:01:26
Checking sstate mirror object availability: 100% |###############| Time: 0:00:13
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
fsbl-2017.2+gitAUTOINC+122565ec40-r0 do_compile: NOTE: fsbl: compiling from external source tree /opt/pkg/petalinux/tools/hsm/data/embeddedsw
ERROR: pmu-firmware-2017.2+gitAUTOINC+122565ec40-r0 do_configure: Function failed: do_configure (log file is located at /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/temp/log.do_configure.71493)
ERROR: Logfile of failure stored in: /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/temp/log.do_configure.71493
Log data follows:
| DEBUG: Executing python function sysroot_cleansstate
| DEBUG: Python function sysroot_cleansstate finished
| DEBUG: Executing shell function do_configure
| MISC_ARG is -yamlconf /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/pmu-firmware.yaml
| APP_ARG is -app "ZynqMP PMU Firmware"
| cmd is: xsct /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/app.tcl -ws /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/../components/plnx_workspace -pname pmu-firmware -rp /opt/pkg/petalinux/tools/hsm/data/embeddedsw -processor psu_pmu_0 -hdf /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/deploy/images/plnx_aarch64/Xilinx-plnx_aarch64.hdf -arch 32 -app "ZynqMP PMU Firmware" -yamlconf /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/pmu-firmware.yaml
| Starting xsdk. This could take few seconds... Eclipse:
| An error has occurred. See the log file
| /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/components/plnx_workspace/.metadata/.log.
| XSCTHELPER INFO: Empty WorkSpace
| Starting xsdk. This could take few seconds... Eclipse:
| An error has occurred. See the log file
| /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/components/plnx_workspace/.metadata/.log.
| timeout while establishing a connection with SDK
| while executing
| "error "timeout while establishing a connection with SDK""
| (procedure "getsdkchan" line 111)
| invoked from within
| "getsdkchan"
| (procedure "::sdk::set_user_repo_path_sdk" line 16)
| invoked from within
| "::sdk::set_user_repo_path_sdk $params(set)"
| (procedure "repo" line 27)
| invoked from within
| "repo -set $path"
| invoked from within
| "if { $params(ws) ne "" } {
| #Local Work Space available
| setws $params(ws)
| if { [catch {importprojects $params(ws)} result] } {
| puts "XSCTHELPER IN..."
| (file "/home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/app.tcl" line 120)
| WARNING: /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/temp/run.do_configure.71493:1 exit 1 from 'xsct /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/app.tcl -ws /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/../components/plnx_workspace -pname pmu-firmware -rp /opt/pkg/petalinux/tools/hsm/data/embeddedsw -processor psu_pmu_0 -hdf /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/deploy/images/plnx_aarch64/Xilinx-plnx_aarch64.hdf -arch 32 -app "ZynqMP PMU Firmware" -yamlconf /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/pmu-firmware.yaml'
| ERROR: Function failed: do_configure (log file is located at /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/tmp/work/plnx_aarch64-xilinx-linux/pmu-firmware/2017.2+gitAUTOINC+122565ec40-r0/temp/log.do_configure.71493)
ERROR: Task (/opt/pkg/petalinux/components/yocto/source/aarch64/layers/meta-xilinx-tools/recipes-bsp/pmu/pmu-firmware_git.bb:do_configure) failed with exit code '1'
解决方法：
AR# 69812
2016.4-2017.2 PetaLinux: Build failed due to "error "timeout while establishing a connection with SDK"'
PetaLinux build can fail with the following timeout error in XSCT:
DEBUG: Executing python function sysroot_cleansstate
DEBUG: Python function sysroot_cleansstate finished
DEBUG: Executing shell function do_configure
MISC_ARG is -yamlconf /tmp/4x10GE-2017.09.12-16.17.33/work/plnx_aarch64-xilinx-linux/fsbl/2017.2+gitAUTOINC+122565ec40-r0/fsbl.yaml
APP_ARG is -app "Zynq MP FSBL"
cmd is: xsct /tmp/4x10GE-2017.09.12-16.17.33/work/plnx_aarch64-xilinx-linux/fsbl/2017.2+gitAUTOINC+122565ec40-r0/app.tcl -ws /home/bryanloz/ZCU102_4PES/4x10GE-Switch/Petalinux/4x10GE/build/../components/plnx_workspace -pname fsbl -rp /proj/petalinux/released/Petalinux-v2017.2/petalinux-v2017.2_0619_1/tools/hsm/data/embeddedsw -processor psu_cortexa53_0 -hdf /tmp/4x10GE-2017.09.12-16.17.33/deploy/images/plnx_aarch64/Xilinx-plnx_aarch64.hdf -arch 64 -app "Zynq MP FSBL" -yamlconf /tmp/4x10GE-2017.09.12-16.17.33/work/plnx_aarch64-xilinx-linux/fsbl/2017.2+gitAUTOINC+122565ec40-r0/fsbl.yaml
Starting xsdk. This could take few seconds... Eclipse:
An error has occurred. See the log file
/home/bryanloz/ZCU102_4PES/4x10GE-Switch/Petalinux/4x10GE/components/plnx_workspace/.metadata/.log.
XSCTHELPER INFO: Empty WorkSpace
Starting xsdk. This could take few seconds... Eclipse:
An error has occurred. See the log file
/home/bryanloz/ZCU102_4PES/4x10GE-Switch/Petalinux/4x10GE/components/plnx_workspace/.metadata/.log.
timeout while establishing a connection with SDK
while executing
"error "timeout while establishing a connection with SDK""
(procedure "getsdkchan" line 111)
invoked from within
"getsdkchan"
(procedure "::sdk::set_user_repo_path_sdk" line 16)
invoked from within
"::sdk::set_user_repo_path_sdk $params(set)"
(procedure "repo" line 27)
invoked from within
"repo -set $path"
invoked from within
"if { $params(ws) ne "" } {
Local Work Space available
setws $params(ws)
if { [catch {importprojects $params(ws)} result] } {
puts "XSCTHELPER IN..."
(file "/tmp/4x10GE-2017.09.12-16.17.33/work/plnx_aarch64-xilinx-linux/fsbl/2017.2+gitAUTOINC+122565ec40-r0/app.tcl" line 120)
WARNING: /tmp/4x10GE-2017.09.12-16.17.33/work/plnx_aarch64-xilinx-linux/fsbl/2017.2+gitAUTOINC+122565ec40-r0/temp/run.do_configure.22432:1 exit 1 from 'eval xsct /tmp/4x10GE-2017.09.12-16.17.33/work/plnx_aarch64-xilinx-linux/fsbl/2017.2+gitAUTOINC+122565ec40-r0/app.tcl -ws /home/bryanloz/ZCU102_4PES/4x10GE-Switch/Petalinux/4x10GE/build/../components/plnx_workspace -pname fsbl -rp /proj/petalinux/released/Petalinux-v2017.2/petalinux-v2017.2_0619_1/tools/hsm/data/embeddedsw -processor psu_cortexa53_0 -hdf /tmp/4x10GE-2017.09.12-16.17.33/deploy/images/plnx_aarch64/Xilinx-plnx_aarch64.hdf -arch 64 ${APP_ARG} ${MISC_ARG}'
ERROR: Function failed: do_configure (log file is located at /tmp/4x10GE-2017.09.12-16.17.33/work/plnx_aarch64-xilinx-linux/fsbl/2017.2+gitAUTOINC+122565ec40-r0/temp/log.do_configure.22432)
解决方案
The following work-arounds can be used to overcome this issue
- Increase the timeout in XSCT.
Create a file with name .xsdbrc in the $HOME directory
Add the line below in the .xsdbrc file
configparams-sdk-launch-timeout 180
- Clean up using the following commands:
rm -rf ~/.Xil
rm -rf ~/.Xilinx
Note: This error could be due to a resource constraint on the PC.
The minimum configuration required for PetaLinux tool installation is 8 cores and 8GB RAM (This is not corrected in 2016.4-2017.2 (UG1144) documentation).
Ideally one project should be built at a time.
If you want to run projects in parallel, set parallel threads and configure execution in petalinux-config->Yocto Settings to lower values which match your system configuration.
[liuwanpeng@localhost xilinx-zcu102-2017.2]$ cd ~
[liuwanpeng@localhost ~]$ echo $HOME
/home/liuwanpeng
[liuwanpeng@localhost ~]$ pwd
/home/liuwanpeng
[liuwanpeng@localhost ~]$ touch .xsdbrc
[liuwanpeng@localhost ~]$ gedit .xsdbrc
[liuwanpeng@localhost ~]$ rm -rf ~/.Xil
[liuwanpeng@localhost ~]$ rm -rf ~/.Xilinx
无效，提示source xxxx/.xsdbrc error。
增加x权限再试,没用
按技术支持提供的方法：
https://forums.xilinx.com/xlnx/board/crawl_message?board.id=EDK&message.id=41823
Xilinx 2016.4 - xsct - Timeout while building fsbl and pmu-firmware
Re: Xilinx 2016.4 - xsct - Timeout while building fsbl and pmu-firmware
Options
10-03-2017 02:05 AM
The reason for failure is xsct uses a locking mechanism which is by default set to /home/user/
you have to change this
in fsbl and pmufw recipes add this two lines
export _JAVA_OPTIONS
_JAVA_OPTIONS = "-Duser.home=${TMPDIR}/xsctenv"
有两个fsbl文件
./project-spec/meta-plnx-generated/recipes-bsp/fsbl/fsbl_%.bbappend
./project-spec/meta-user/recipes-bsp/fsbl/fsbl_%.bbappend
一个mufw
./project-spec/meta-plnx-generated/recipes-bsp/pmu/pmu-firmware_%.bbappend
都加上
我擦，真的编过去了，用了上面的方法：
[liuwanpeng@localhost xilinx-zcu102-2017.2]$ petalinux-build
[INFO] building project
[INFO] sourcing bitbake
INFO: bitbake petalinux-user-image
Loading cache: 100% |############################################| Time: 0:00:02
Loaded 3235 entries from dependency cache.
Parsing recipes: 100% |##########################################| Time: 0:00:07
Parsing of 2446 .bb files complete (2407 cached, 39 parsed). 3236 targets, 224 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
Initialising tasks: 100% |#######################################| Time: 0:00:40
Checking sstate mirror object availability: 100% |###############| Time: 0:00:17
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
fsbl-2017.2+gitAUTOINC+122565ec40-r0 do_compile: NOTE: fsbl: compiling from external source tree /opt/pkg/petalinux/tools/hsm/data/embeddedsw
pmu-firmware-2017.2+gitAUTOINC+122565ec40-r0 do_compile: NOTE: pmu-firmware: compiling from external source tree /opt/pkg/petalinux/tools/hsm/data/embeddedsw
NOTE: Tasks Summary: Attempted 2445 tasks of which 1869 didn't need to be rerun and all succeeded.
INFO: generating FIT Image
INFO: bitbake petalinux-user-image -R /home/liuwanpeng/mpsoc/xilinx-zcu102-2017.2/build/conf/fit-image.conf
Parsing recipes: 100% |##########################################| Time: 0:04:21
Parsing of 2446 .bb files complete (0 cached, 2446 parsed). 3236 targets, 224 skipped, 0 masked, 0 errors.
NOTE: Resolving any missing task queue dependencies
Initialising tasks: 100% |#######################################| Time: 0:00:21
Checking sstate mirror object availability: 100% |###############| Time: 0:00:03
NOTE: Executing SetScene Tasks
NOTE: Executing RunQueue Tasks
NOTE: Tasks Summary: Attempted 2446 tasks of which 2419 didn't need to be rerun and all succeeded.
INFO: Copying Images from deploy to images
INFO: Creating images/linux directory
[INFO] successfully built project
