用Qemu模拟vexpress-a9 （五） --- u-boot引导kernel，device tree的使用

make CROSS_COMPILE=arm-linux-gnueabi- ARCH=arm O=./out_vexpress_3_16 dtbs

vexpress-v2p-ca15_a7.dtb vexpress-v2p-ca15-tc1.dtb vexpress-v2p-ca5s.dtb vexpress-v2p-ca9.dtb

cp out_vexpress_3_16/arch/arm/boot/dts/vexpress-v2p-ca9.dtb /tftpboot/dtb

qemu-system-arm -M vexpress-a9 \
-kernel /root/tq2440_work/u-boot/u-boot/u-boot \
-nographic \
-m 512M \
-net nic,vlan= -net tap,vlan=,ifname=tap0 \
-sd /root/tq2440_work/busybox_study/a9rootfs.ext3

setenv bootargs 'root=/dev/mmcblk0 console=ttyAMA0'
tftp 0x60003000 uImage
tftp 0x60500000 dtb
bootm 0x60003000 - 0x60500000

U-Boot 2015.07-rc3--gf3edfd3-dirty (Dec - :: -)DRAM: MiB
WARNING: Caches not enabled
Flash: MiB
MMC: MMC:
*** Warning - bad CRC, using default environmentIn: serial
Out: serial
Err: serial
Net: smc911x-
Warning: smc911x- using MAC address from net deviceHit any key to stop autoboot:
VExpress# setenv bootargs 'root=/dev/mmcblk0 console=ttyAMA0'
VExpress# tftp 0x60003000 uImage
smc911x: MAC :::::
smc911x: detected LAN9118 controller
smc911x: phy initialized
smc911x: MAC :::::
Using smc911x- device
TFTP from server 192.168.11.20; our IP address is 192.168.11.5
Filename 'uImage'.
Load address: 0x60003000
Loading: #################################################################
#################################################################
#################################################################
################################
698.2 KiB/s
done
Bytes transferred = (32cd30 hex)
smc911x: MAC :::::
VExpress# tftp 0x60500000 dtb
smc911x: MAC :::::
smc911x: detected LAN9118 controller
smc911x: phy initialized
smc911x: MAC :::::
Using smc911x- device
TFTP from server 192.168.11.20; our IP address is 192.168.11.5
Filename 'dtb'.
Load address: 0x60500000
Loading: #
971.7 KiB/s
done
Bytes transferred = (328d hex)
smc911x: MAC :::::
VExpress# bootm 0x60003000 - 0x60500000
## Booting kernel from Legacy Image at ...
Image Name: Linux-3.16.
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: Bytes = 3.2 MiB
Load Address:
Entry Point:
Verifying Checksum ... OK
## Flattened Device Tree blob at
Booting using the fdt blob at 0x60500000
Loading Kernel Image ... OK
Loading Device Tree to 7fee2000, end 7fee828c ... OKStarting kernel ...Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Linux version 3.16. (root@ubuntu) (gcc version 4.7. (Ubuntu/Linaro 4.7.-12ubuntu1) ) # SMP Sun Dec :: PST
CPU: ARMv7 Processor [410fc090] revision (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine model: V2P-CA9
Memory policy: Data cache writeback
CPU: All CPU(s) started in SVC mode.
PERCPU: Embedded pages/cpu @9ffcf000 s7552 r8192 d12928 u32768
Built zonelists in Zone order, mobility grouping on. Total pages:
Kernel command line: root=/dev/mmcblk0 console=ttyAMA0
PID hash table entries: (order: , bytes)
Dentry cache hash table entries: (order: , bytes)
Inode-cache hash table entries: (order: , bytes)
Memory: 513148K/524288K available (4567K kernel code, 191K rwdata, 1292K rodata, 239K init, 149K bss, 11140K reserved)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( kB)
fixmap : 0xffc00000 - 0xffe00000 ( kB)
vmalloc : 0xa0800000 - 0xff000000 ( MB)
lowmem : 0x80000000 - 0xa0000000 ( MB)
modules : 0x7f000000 - 0x80000000 ( MB)
.text : 0x80008000 - 0x805c1238 ( kB)
.init : 0x805c2000 - 0x805fdd80 ( kB)
.data : 0x805fe000 - 0x8062dc20 ( kB)
.bss : 0x8062dc28 - 0x806533ec ( kB)
SLUB: HWalign=, Order=-, MinObjects=, CPUs=, Nodes=
Hierarchical RCU implementation.
RCU restricting CPUs from NR_CPUS= to nr_cpu_ids=.
RCU: Adjusting geometry for rcu_fanout_leaf=, nr_cpu_ids=
NR_IRQS: nr_irqs:
GIC CPU mask not found - kernel will fail to boot.
GIC CPU mask not found - kernel will fail to boot.
sched_clock: bits at 24MHz, resolution 41ns, wraps every 178956969942ns
Console: colour dummy device 80x30
Calibrating delay loop... 398.13 BogoMIPS (lpj=)
pid_max: default: minimum:
Mount-cache hash table entries: (order: , bytes)
Mountpoint-cache hash table entries: (order: , bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -, cpu , socket , mpidr
Setting up static identity map for 0x60455850 - 0x604558a8
CPU1: failed to boot: -
CPU2: failed to boot: -
CPU3: failed to boot: -
Brought up CPUs
SMP: Total of processors activated.
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.: implementor architecture part variant rev
regulator-dummy: no parameters
NET: Registered protocol family
DMA: preallocated KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
of_amba_device_create(): amba_device_add() failed (-) for /memory-controller@100e0000
of_amba_device_create(): amba_device_add() failed (-) for /memory-controller@100e1000
of_amba_device_create(): amba_device_add() failed (-) for /watchdog@100e5000
of_amba_device_create(): amba_device_add() failed (-) for /smb/motherboard/iofpga@,/sysctl@
of_amba_device_create(): amba_device_add() failed (-) for /smb/motherboard/iofpga@,/wdt@0f000
hw-breakpoint: debug architecture 0x4 unsupported.
Serial: AMBA PL011 UART driver
.uart: ttyAMA0 at MMIO 0x10009000 (irq = , base_baud = ) is a PL011 rev1
console [ttyAMA0] enabled
1000a000.uart: ttyAMA1 at MMIO 0x1000a000 (irq = , base_baud = ) is a PL011 rev1
1000b000.uart: ttyAMA2 at MMIO 0x1000b000 (irq = , base_baud = ) is a PL011 rev1
1000c000.uart: ttyAMA3 at MMIO 0x1000c000 (irq = , base_baud = ) is a PL011 rev1
3V3: mV
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Initialized.
Switched to clocksource arm,sp804
NET: Registered protocol family
TCP established hash table entries: (order: , bytes)
TCP bind hash table entries: (order: , bytes)
TCP: Hash tables configured (established bind )
TCP: reno registered
UDP hash table entries: (order: , bytes)
UDP-Lite hash table entries: (order: , bytes)
NET: Registered protocol family
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4. backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, counters available
futex hash table entries: (order: , bytes)
squashfs: version 4.0 (//) Phillip Lougher
jffs2: version 2.2. (NAND) © - Red Hat, Inc.
9p: Installing v9fs 9p2000 file system support
msgmni has been set to
io scheduler noop registered (default)
clcd-pl11x: probe of .clcd failed with error -
clcd-pl11x: probe of 1001f000.clcd failed with error -
VD10: at mV
VD10_S2: at mV
VD10_S3: at mV
VCC1V8: at mV
DDR2VTT: at mV
VCC3V3: at mV
VIO: at mV
.flash: Found x16 devices at 0x0 in -bit bank. Manufacturer ID 0x000000 Chip ID 0x000000
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
.flash: Found x16 devices at 0x0 in -bit bank. Manufacturer ID 0x000000 Chip ID 0x000000
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
Concatenating MTD devices:
(): "40000000.flash"
(): "40000000.flash"
into device "40000000.flash"
libphy: smsc911x-mdio: probed
smsc911x 4e000000.ethernet eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=4e000000.etherne:, irq=-)
smsc911x 4e000000.ethernet eth0: MAC Address: :::::
nxp-isp1760 4f000000.usb: NXP ISP1760 USB Host Controller
nxp-isp1760 4f000000.usb: new USB bus registered, assigned bus number
nxp-isp1760 4f000000.usb: Scratch test failed.
nxp-isp1760 4f000000.usb: can't setup: -19
nxp-isp1760 4f000000.usb: USB bus deregistered
usbcore: registered new interface driver usb-storage
mousedev: PS/ mouse device common for all mice
rtc-pl031 .rtc: rtc core: registered pl031 as rtc0
mmci-pl18x .mmci: Got CD GPIO #.
mmci-pl18x .mmci: Got WP GPIO #.
mmci-pl18x .mmci: No vqmmc regulator found
mmci-pl18x .mmci: mmc0: PL181 manf rev0 at 0x10005000 irq , (pio)
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
input: AT Raw Set keyboard as /devices/smb/smb:motherboard/smb:motherboard:iofpga@,/.kmi/serio0/input/input0
mmc0: new SD card at address
mmcblk0: mmc0: QEMU! 32.0 MiB
mmcblk0: unknown partition table
aaci-pl041 .aaci: ARM AC'97 Interface PL041 rev0 at 0x10004000, irq 43
aaci-pl041 .aaci: FIFO entries
oprofile: using arm/armv7-ca9
TCP: cubic registered
NET: Registered protocol family
9pnet: Installing 9P2000 support
rtc-pl031 .rtc: setting system clock to -- :: UTC ()
ALSA device list:
#: ARM AC'97 Interface PL041 rev0 at 0x10004000, irq 43
input: ImExPS/ Generic Explorer Mouse as /devices/smb/smb:motherboard/smb:motherboard:iofpga@,/.kmi/serio1/input/input2
EXT3-fs (mmcblk0): recovery required on readonly filesystem
EXT3-fs (mmcblk0): write access will be enabled during recovery
kjournald starting. Commit interval seconds
EXT3-fs (mmcblk0): recovery complete
EXT3-fs (mmcblk0): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) readonly on device :.
Freeing unused kernel memory: 236K (805c2000 - 805fd000)
random: nonblocking pool is initialized
smsc911x 4e000000.ethernet eth0: SMSC911x/921x identified at 0xa0900000, IRQ: Please press Enter to activate this console. [root@vexpress ]#
[root@vexpress ]#
[root@vexpress ]# ls /proc/device-tree/
#address-cells memory-controller@100e0000
#size-cells memory-controller@100e1000
aliases memory@
arm,hbi model
arm,vexpress,site name
cache-controller@1e00a000 pmu
chosen scu@1e000000
clcd@ smb
compatible timer@100e4000
cpus timer@1e000600
dcc watchdog@100e5000
interrupt-controller@1e001000 watchdog@1e000620

qemu-system-arm \
-M vexpress-a9 \
-m 512M \
-kernel /root/tq2440_work/kernel/linux-stable/out_vexpress_3_16/arch/arm/boot/zImage \
-nographic \
-append "root=/dev/mmcblk0 console=ttyAMA0" \
-sd /root/tq2440_work/busybox_study/a9rootfs.ext3 \
-dtb /tftpboot/dtb

Booting Linux on physical CPU 0x0
Initializing cgroup subsys cpuset
Linux version 3.16. (root@ubuntu) (gcc version 4.7. (Ubuntu/Linaro 4.7.-12ubuntu1) ) # SMP Sun Dec :: PST
CPU: ARMv7 Processor [410fc090] revision (ARMv7), cr=10c53c7d
CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine model: V2P-CA9
Memory policy: Data cache writeback
CPU: All CPU(s) started in SVC mode.
PERCPU: Embedded pages/cpu @9fbcf000 s7552 r8192 d12928 u32768
Built zonelists in Zone order, mobility grouping on. Total pages:
Kernel command line: root=/dev/mmcblk0 console=ttyAMA0
PID hash table entries: (order: , bytes)
Dentry cache hash table entries: (order: , bytes)
Inode-cache hash table entries: (order: , bytes)
Memory: 513116K/524288K available (4567K kernel code, 191K rwdata, 1292K rodata, 239K init, 149K bss, 11172K reserved)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( kB)
fixmap : 0xffc00000 - 0xffe00000 ( kB)
vmalloc : 0xa0800000 - 0xff000000 ( MB)
lowmem : 0x80000000 - 0xa0000000 ( MB)
modules : 0x7f000000 - 0x80000000 ( MB)
.text : 0x80008000 - 0x805c1238 ( kB)
.init : 0x805c2000 - 0x805fdd80 ( kB)
.data : 0x805fe000 - 0x8062dc20 ( kB)
.bss : 0x8062dc28 - 0x806533ec ( kB)
SLUB: HWalign=, Order=-, MinObjects=, CPUs=, Nodes=
Hierarchical RCU implementation.
RCU restricting CPUs from NR_CPUS= to nr_cpu_ids=.
RCU: Adjusting geometry for rcu_fanout_leaf=, nr_cpu_ids=
NR_IRQS: nr_irqs:
GIC CPU mask not found - kernel will fail to boot.
GIC CPU mask not found - kernel will fail to boot.
sched_clock: bits at 24MHz, resolution 41ns, wraps every 178956969942ns
Console: colour dummy device 80x30
Calibrating delay loop... 286.10 BogoMIPS (lpj=)
pid_max: default: minimum:
Mount-cache hash table entries: (order: , bytes)
Mountpoint-cache hash table entries: (order: , bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -, cpu , socket , mpidr
Setting up static identity map for 0x60455850 - 0x604558a8
CPU1: failed to boot: -
CPU2: failed to boot: -
CPU3: failed to boot: -
Brought up CPUs
SMP: Total of processors activated.
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.: implementor architecture part variant rev
regulator-dummy: no parameters
NET: Registered protocol family
DMA: preallocated KiB pool for atomic coherent allocations
cpuidle: using governor ladder
cpuidle: using governor menu
of_amba_device_create(): amba_device_add() failed (-) for /memory-controller@100e0000
of_amba_device_create(): amba_device_add() failed (-) for /memory-controller@100e1000
of_amba_device_create(): amba_device_add() failed (-) for /watchdog@100e5000
of_amba_device_create(): amba_device_add() failed (-) for /smb/motherboard/iofpga@,/sysctl@
of_amba_device_create(): amba_device_add() failed (-) for /smb/motherboard/iofpga@,/wdt@0f000
hw-breakpoint: debug architecture 0x4 unsupported.
Serial: AMBA PL011 UART driver
.uart: ttyAMA0 at MMIO 0x10009000 (irq = , base_baud = ) is a PL011 rev1
console [ttyAMA0] enabled
1000a000.uart: ttyAMA1 at MMIO 0x1000a000 (irq = , base_baud = ) is a PL011 rev1
1000b000.uart: ttyAMA2 at MMIO 0x1000b000 (irq = , base_baud = ) is a PL011 rev1
1000c000.uart: ttyAMA3 at MMIO 0x1000c000 (irq = , base_baud = ) is a PL011 rev1
3V3: mV
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Advanced Linux Sound Architecture Driver Initialized.
Switched to clocksource arm,sp804
NET: Registered protocol family
TCP established hash table entries: (order: , bytes)
TCP bind hash table entries: (order: , bytes)
TCP: Hash tables configured (established bind )
TCP: reno registered
UDP hash table entries: (order: , bytes)
UDP-Lite hash table entries: (order: , bytes)
NET: Registered protocol family
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4. backchannel transport module.
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, counters available
futex hash table entries: (order: , bytes)
squashfs: version 4.0 (//) Phillip Lougher
jffs2: version 2.2. (NAND) © - Red Hat, Inc.
9p: Installing v9fs 9p2000 file system support
msgmni has been set to
io scheduler noop registered (default)
clcd-pl11x: probe of .clcd failed with error -
clcd-pl11x: probe of 1001f000.clcd failed with error -
VD10: at mV
VD10_S2: at mV
VD10_S3: at mV
VCC1V8: at mV
DDR2VTT: at mV
VCC3V3: at mV
VIO: at mV
.flash: Found x16 devices at 0x0 in -bit bank. Manufacturer ID 0x000000 Chip ID 0x000000
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
.flash: Found x16 devices at 0x0 in -bit bank. Manufacturer ID 0x000000 Chip ID 0x000000
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
Concatenating MTD devices:
(): "40000000.flash"
(): "40000000.flash"
into device "40000000.flash"
libphy: smsc911x-mdio: probed
smsc911x 4e000000.ethernet eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=4e000000.etherne:, irq=-)
smsc911x 4e000000.ethernet eth0: MAC Address: :::::
nxp-isp1760 4f000000.usb: NXP ISP1760 USB Host Controller
nxp-isp1760 4f000000.usb: new USB bus registered, assigned bus number
nxp-isp1760 4f000000.usb: Scratch test failed.
nxp-isp1760 4f000000.usb: can't setup: -19
nxp-isp1760 4f000000.usb: USB bus deregistered
usbcore: registered new interface driver usb-storage
mousedev: PS/ mouse device common for all mice
rtc-pl031 .rtc: rtc core: registered pl031 as rtc0
mmci-pl18x .mmci: Got CD GPIO #.
mmci-pl18x .mmci: Got WP GPIO #.
mmci-pl18x .mmci: No vqmmc regulator found
mmci-pl18x .mmci: mmc0: PL181 manf rev0 at 0x10005000 irq , (pio)
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
input: AT Raw Set keyboard as /devices/smb/smb:motherboard/smb:motherboard:iofpga@,/.kmi/serio0/input/input0
mmc0: new SD card at address
mmcblk0: mmc0: QEMU! 32.0 MiB
mmcblk0: unknown partition table
aaci-pl041 .aaci: ARM AC'97 Interface PL041 rev0 at 0x10004000, irq 43
aaci-pl041 .aaci: FIFO entries
oprofile: using arm/armv7-ca9
TCP: cubic registered
NET: Registered protocol family
9pnet: Installing 9P2000 support
rtc-pl031 .rtc: setting system clock to -- :: UTC ()
ALSA device list:
#: ARM AC'97 Interface PL041 rev0 at 0x10004000, irq 43
input: ImExPS/ Generic Explorer Mouse as /devices/smb/smb:motherboard/smb:motherboard:iofpga@,/.kmi/serio1/input/input2
kjournald starting. Commit interval seconds
EXT3-fs (mmcblk0): mounted filesystem with writeback data mode
VFS: Mounted root (ext3 filesystem) readonly on device :.
Freeing unused kernel memory: 236K (805c2000 - 805fd000)
random: nonblocking pool is initialized
smsc911x 4e000000.ethernet eth0: SMSC911x/921x identified at 0xa0900000, IRQ: Please press Enter to activate this console. [root@vexpress ]#